Misc EMF Protection
|
| |
Product |
Price |
View |
|
Compass
Looking for the cheapest way to determine if something is magnetized?
Want a simple device for comparing magnets? Doing a school project?
Lost? For hundreds of years, mankind has used the trusty compass to
guide him through the Earth?s magnetic field. Measure the deflection of
the needle from magnetic North at known distances using this nice 1-3/8
inch diameter compass to quantify and compare DC magnetic fields, track
down magnetized components, or evaluate magnetic shielding performance.
Much cleaner than iron filings. Makes a great science fair project too.
Includes a loop for your keychain, charm bracelet, or necklace. Compass
must be held horizontally to operate.
|
2.50 |
View |
|
Electrical Sensitivity Diagnotic Kit Adapters
Adapters Include:
USA flat plug
British square plug
Australian flat plug
European 4mm round plug
simple carry case
Note, you may also need a 240V to 120V transformer.
|
10.00 |
View |
|
Zero Gauss Chamber
This chamber can be used with the
KiloGaussmeter
or
Geomagnetometer to
provide a zero gauss (magnetic field-free environment) reference,
enabling you to take absolute readings of the ambient magnetic field
(the Earth's magnetic field is typically around 500 mG). Concentric
welded 12" long tubes (?" ID chamber) with stand, made of high
permeability magnetic shielding alloy provide excellent shielding.
|
350.00 |
View |
|
StrikeAlert
StrikeAlert is a small and affordable lightning detector that provides
an early warning of approaching lightning strikes from as far away as
40 miles and lets you know if the storm is coming your way or moving
away. An audible alarm allows you to determine the storm's activity
without having to visually monitor the unit and sounds when there's a
strike. A corresponding LED light illuminates to indicate lightning at
distances of 20-40 miles, 12-24 miles, 6-12 miles and within 6 miles.
The detector is housed in a small pager-like casing that can be clipped
on a belt and runs up to 100 hours on a single AA battery.
Perfect for kite flyers, golfers, sailors, pilots, athletes, beach
goers and anyone who spends work or leisure time outdoors. Paranormal
investigators can also use the StrikeAlert to monitor for unusual
lightning-like activity.
|
79.95 |
View |
|
Radiation Check Source
Cesium-137, 0.1 microCi calibration
standard mounted in a 1? plastic disk. 30.1 year half life. Emits Gamma
& Beta. Use it to test your Geiger Counter?s performance.
No special handling, storage, shipping, or disposal required. Presents no known radiation hazard.
|
65.00 |
View |
|
Bio-Grounder
When we tested it, we were amazed at how well this device does
what it claims. Place this simple pad on your car seat and attach the
provided ground wire to any portion of the metal seat frame. The
Bio-Grounder drains away body voltage which otherwise builds up (90 mV
or more in some tests!) This body voltage has been shown to add tension
to the nervous system, increase heart rate and accelerate fatigue.
Bio-Grounder may reduce symptoms electrically sensitive
individuals typically experience in the car. Drivers report a calm
increased alertness, less fatigue, and less tendency for road rage! Can
be used in any car or truck. One size fits all. Get one for each
passenger.
Seat not included and is shown in picture for demonstration purposes only.
|
29.95 |
View |
|
Vehicle Ground Strap
No one likes that awful big
shock when getting out of an automobile or truck. That shock is the
discharge of "chassis voltage" built up as the vehicle moves along the
highway. What you might not know is that in addition to causing
symptoms of high body voltage in the driver and passengers (such as
fatigue, irritability, drowsiness, and motion sickness), this type of
discharge causes serious injury when it occurs at the gas pump. Every
year, this seemingly innocent spark occurs at the wrong place and the
wrong time: igniting gasoline vapors while fueling the vehicle. This is
prevented by grounding the vehicle.
The Vehicle Ground Strap can be used on any car
or truck. Simply affix the strap's clamp to the chassis of the vehicle
and allow the conductive strap to dangle to the ground. Safe, durable
and unaffected by the weather, the Vehicle Ground Strap maintains a
secure ground and electrically neutral vehicle. Makes a great gift too.
18" long, 1 year warranty.
|
19.95 |
View |
|
Nickel/Copper Fabric Tape
High conductivity, high flexibility fabric tape with conductive
adhesive. Nickel and Copper coated nylon ripstop fabric (with
anti-fray) offers excellent RF shielding properties (82 dB at 1 MHz)
and electrical conductivity (surface resistivity of less than 0.1
Ohms/sq). Use it so seal gaps, seams, and edges of shielding fabrics,
paints or plastics. Also can be used to create conductive pathways on
surfaces or add shielding to cables and flexible conduits. Cuts easily
with scissors. Extremely corrosion and tear resistant, -40 to 250 ?F. 1
inch wide, 25 feet per roll.
|
19.95 |
View |
|
Stretch Silver Conductive Fabric
This medical grade Silver plated 92% Nylon 8% Dorlastan fabric offers the unique ability to stretch in both directions. Can be used as an antibacterial wound dressing (note: our material is not sterile) but it also makes a great material for electrode contacts, stretchy hats, socks, gloves, or other garments. Highly conducutive.
Width: 135 cm wide (52 inches)
Weight: 130 g/m˛
Thickness: 0.50 mm
Stretch: ~100% in length direction; ~65% in width direction
Surface resistivity is |
59.95 |
View |
|
Laminated Microwave Absorber Sheet
NEW IMPROVED
MICROWAVE ABSORBING SHEET
NOTE: This product is sold by Linear Foot. Enter the number of feet you want in the quantity box before adding it to your cart. For example, if you want 30 linear feet, enter 30 in the qty box then press add to cart. Failure to do so will result in only 1 linear foot being shipped to you.
Now with plastic coating for easier handling
Carbon is conductive in some forms, and a very good microwave absorber. Using non-woven nearly-pure carbon fibers, to achieve both good microwave shielding and high absorption, this unique material has the following specifications:
Carbon base material (without plastic laminate):
Width: 48 inch (1219 mm)
Weight: 34 g/m˛
Thickness: 18 mil (0.445 mm)
Resistivity: ~3 Ohms per square
Tensile: 47 N/15mm
We are pleased to offer this improved version of our very low cost microwave absorber sheet. This version is plastic laminated on both sides. This gives better durability and easier handling. Dust is reduced and skin contact is not a problem.
Application Note:
To create a super high peformance enclosure, you can combine a layer of this Microwave Absorber material with a layer of a high performance fabric shield such as Flectron or Zelt. Line the inside of the shield with Absorber... it will scavenge any RF which might leak in.
Super light weight. Can be used to line walls and containers, make drapes or partitions. Does not permit air circulation, minimal light penetration.
Still 48 inches wide, but surface is non-conductive due to laminate. Request roll shipping if you need to avoid creases from folding.
NOTE: This product is sold by Linear Foot. Enter the number of feet you want in the quantity box before adding it to your cart. For example, if you want 30 linear feet, enter 30 in the qty box then press add to cart. Failure to do so will result in only 1 linear foot being shipped to you. |
8.95 |
View |
|
|
PaperShield
For small shielding job where you don?t need a high attenuation, this
unique material is just the ticket. Only 0.010 inch thick, PaperSHIELD
is flexible and can be easily cut with a scissors and shaped by hand
into simple or very complex shapes. High saturation and moderate
permeability make this ideal for shielding magnets. White paper on one
side can be imprinted (by you), peel and stick adhesive on the other
side permits easy and semi-permanent mounting almost anywhere. Magnets
will stick to it nicely. Really great for experimenting. 36 inches
wide. Made in USA.
|
11.95 |
View |
|
MagnetShield
First line of defense for shielding strong
magnetic fields from magnets, speakers, small transformers and motors.
Strong magnetic fields are harder to shield because they tend to
"saturate" the shielding material. This 4" wide foil is a hefty .010"
thick and 250' long and has an exceptionally high magnetic saturation of 21400 Gauss
and maximum permeability of 4000. Tin plated for excellent corrosion
resistance and better conductivity, it can be soldered or painted.
MagnetShield typically reduces fields up to a factor of 2 or 3
depending on size/shape of the shield. Can be used in multiple layers,
and/or in combination with a higher permeability alloy such as
Joint-Shield for higher attenuation. Annealing is not necessary with
this material.
Mechanical Specifications
Specific Gravity:
7.86
Coefficient of Expansion:
13.7 x 10-6 per °C
Tensile Strength:
42 x 10? PSI
Yield Strength:
27 x 10? PSI
Mod. of Elasticity:
30 x 106 PSI
Hardness (Rockwell B):
50 Ref.
Melting Point:
2789.6?F
Thermal Conductivity:
0.118 cal/sec/cm?/cm/?C at 20?C
Minimum Operating Temp:
4?K
Curie Temp:
1418?F
Carbon Content:
.07%
Electromagnetic Specifications
Electrical Resistivity:
64 ohms/cir mil-foot
Saturation Induction:
21,400 Gauss
Initial Permeabilty:
200
Permeability at 40 B:
300
Permeability at 200 B:
500
Maximum Permeability:
4000
Induction at m max.:
8000
Coercive Force:
1.0 Hc, Oersteds
Annealing is not as critical with this material as it is with the high
permeability materials (foil, Joint-Shield, Mag-Stop).
|
4.50 |
View |
|
|
MagnetShield 250' Roll
First line of defense for shielding strong
magnetic fields from magnets, speakers, small transformers and motors.
Strong magnetic fields are harder to shield because they tend to
"saturate" the shielding material. This 4" wide foil is a hefty .010"
thick and 250' long and has an exceptionally high magnetic saturation of 21400 Gauss
and maximum permeability of 4000. Tin plated for excellent corrosion
resistance and better conductivity, it can be soldered or painted.
MagnetShield typically reduces fields up to a factor of 2 or 3
depending on size/shape of the shield. Can be used in multiple layers,
and/or in combination with a higher permeability alloy such as
Joint-Shield for higher attenuation. Annealing is not necessary with
this material.
Mechanical Specifications
Specific Gravity:
7.86
Coefficient of Expansion:
13.7 x 10-6 per °C
Tensile Strength:
42 x 10? PSI
Yield Strength:
27 x 10? PSI
Mod. of Elasticity:
30 x 106 PSI
Hardness (Rockwell B):
50 Ref.
Melting Point:
2789.6?F
Thermal Conductivity:
0.118 cal/sec/cm?/cm/?C at 20?C
Minimum Operating Temp:
4?K
Curie Temp:
1418?F
Carbon Content:
.07%
Electromagnetic Specifications
Electrical Resistivity:
64 ohms/cir mil-foot
Saturation Induction:
21,400 Gauss
Initial Permeabilty:
200
Permeability at 40 B:
300
Permeability at 200 B:
500
Maximum Permeability:
4000
Induction at m max.:
8000
Coercive Force:
1.0 Hc, Oersteds
Annealing is not as critical with this material as it is with the high
permeability materials (foil, Joint-Shield, Mag-Stop).
|
844.00 |
View |
|
The EarthCalm Package - Ultimate 1
A note from the inventor of EarthCalm Products | EarthCalm Testimonials | EarthCalm FAQ's | EarthCalm Brochure | What is the Schumann Resonance? | What is the difference between an EarthCalm Resonator and the Q-Link pendant? | Cell Phone and Cordless Phone protection | Headaches & Migraines | Fibromyalgia & Electrical Sensitivity | Children, ADHD & Asthma | Protect yourself
Free Shipping on this Item!
Get 10% off when you buy TWO or more EarthCalm productsWe give you this 10% off package using the EarthCalm Home or Office Unit and the EarthCalm Resonator as the combination of these items produces better results
Consists of:
One Home Protection System
One Personal Scalar Resonator
The Ultimate Pack over time will result in a noticeable increase in overall health as well as alleviation of chronic symptoms such as headaches, asthma, hyperactivity, mood swings, etc. There is an additional enhancement when you double the EarthCalm 14 circuits to 28. The Ultimate Pack consists of one Scalar Resonator and one Scalar Home Protection System.
The Scalar Resonator
The EarthCalm Scalar Resonator is our maximum strength personal pendant. It consists of 7 EarthCalm circuits exactly matched by another set of 7 EarthCalm circuits for a total of 14 circuits. The resulting Scalar Resonance Technology maximizes protection from EMFs by amplifying your electrical grounding into the earth.
A scalar wave is generated whenever one wave is matched by the opposite frequency and amplitude of another wave such that they cancel each other out. The result is not zero, but rather another dimension is activated, which is non local (everywhere at once) and is theorized to be responsible for healing. The increased scalar waves generated by your nervous system when you are wearing a Scalar Resonator will bring you into greater balance with the earth
Notice to Researchers: EarthCalm is looking for a reputable Research Team who would be willing to conduct scientific research on the efficacy of EarthCalm Home Protectors for ADHD and Asthmatic conditions in children.
EarthCalm products never need 'recharging' and are offered with a 90 day money back guarantee to encourage you to experiment with this product yourself. This item can be returned in 90 days for a credit minus a $7.99 shipping fee for the 48 States. |
465.00 |
View |
|
|
MagneticShield 36"x15"x0.15" plate
First line of defense for shielding strong
magnetic fields from magnets, speakers, small transformers and motors.
Strong magnetic fields are harder to shield because they tend to
"saturate" the shielding material. This plate has an exceptionally high magnetic saturation of 21400 Gauss
and maximum permeability of 4000. Tin plated for excellent corrosion
resistance and better conductivity, it can be soldered or painted.
MagnetShield typically reduces fields up to a factor of 2 or 3
depending on size/shape of the shield. Can be used in multiple layers,
and/or in combination with a higher permeability alloy such as
Joint-Shield for higher attenuation. Annealing is not necessary with
this material.
Mechanical Specifications
Specific Gravity:
7.86
Coefficient of Expansion:
13.7 x 10-6 per ?C
Tensile Strength:
42 x 10? PSI
Yield Strength:
27 x 10? PSI
Mod. of Elasticity:
30 x 106 PSI
Hardness (Rockwell B):
50 Ref.
Melting Point:
2789.6?F
Thermal Conductivity:
0.118 cal/sec/cm?/cm/?C at 20?C
Minimum Operating Temp:
4?K
Curie Temp:
1418?F
Carbon Content:
.07%
Electromagnetic Specifications
Electrical Resistivity:
64 ohms/cir mil-foot
Saturation Induction:
21,400 Gauss
Initial Permeabilty:
200
Permeability at 40 B:
300
Permeability at 200 B:
500
Maximum Permeability:
4000
Induction at m max.:
8000
Coercive Force:
1.0 Hc, Oersteds
Annealing is not as critical with this material as it is with the high
permeability materials (foil, Joint-Shield, Mag-Stop).
Dimensions:
Width: 36"
Height: 15"
Thickness: 0.15" |
39.00 |
View |
|
|
MagneticShield 36"x120"x0.15" plate
First line of defense for shielding strong
magnetic fields from magnets, speakers, small transformers and motors.
Strong magnetic fields are harder to shield because they tend to
"saturate" the shielding material. This plate has an exceptionally high magnetic saturation of 21400 Gauss
and maximum permeability of 4000. Tin plated for excellent corrosion
resistance and better conductivity, it can be soldered or painted.
MagnetShield typically reduces fields up to a factor of 2 or 3
depending on size/shape of the shield. Can be used in multiple layers,
and/or in combination with a higher permeability alloy such as
Joint-Shield for higher attenuation. Annealing is not necessary with
this material.
Mechanical Specifications
Specific Gravity:
7.86
Coefficient of Expansion:
13.7 x 10-6 per ?C
Tensile Strength:
42 x 10? PSI
Yield Strength:
27 x 10? PSI
Mod. of Elasticity:
30 x 106 PSI
Hardness (Rockwell B):
50 Ref.
Melting Point:
2789.6?F
Thermal Conductivity:
0.118 cal/sec/cm?/cm/?C at 20?C
Minimum Operating Temp:
4?K
Curie Temp:
1418?F
Carbon Content:
.07%
Electromagnetic Specifications
Electrical Resistivity:
64 ohms/cir mil-foot
Saturation Induction:
21,400 Gauss
Initial Permeabilty:
200
Permeability at 40 B:
300
Permeability at 200 B:
500
Maximum Permeability:
4000
Induction at m max.:
8000
Coercive Force:
1.0 Hc, Oersteds
Annealing is not as critical with this material as it is with the high
permeability materials (foil, Joint-Shield, Mag-Stop).
Dimensions:
Width: 36"
Height: 120"
Thickness: 0.15" |
259.00 |
View |
|
Magnetic Shielding Foil 15inch wide, 0.004inch thick
Price is per linear foot. Please enter the the desired length (per linear ft) in the quantity box
Used for years in industry to shield delicate electronic components
from EMFs, magnetic shielding alloy is now available at affordable
prices for home and office use. This 80% nickel alloy is easy to trim
with scissors and shape by hand. Can be formed into magnetic barriers
on cellular phones, microwave ovens, doorbell transformers, VDTs,
buried wiring, and more. With snug fitting shapes, get as much as 75%
attenuation of the magnetic field with one thickness. Use multiple
layers for even greater reduction. Foil is available in two sizes and
can be ordered in any length. (We recommend the use of a
gaussmeter
to determine the proper shape and positioning of the magnetic shield,
and to confirm that the fields have been adequately reduced.)
CAUTION: Foil has sharp edges!
SPECIFICATIONS:
Thickness: 0.004"
Temper: Stress Annealed
Specification: MIL N 14411c
Grain Size: 10
Hardness: HV 0.3 = 188
Coercive Force: HC = 0.007 Oersteds
Max. Permeability: MUMAX = 325000
Saturation Induction: B (10 OE) = 7500 G
Chemical Analysis:
Ni: 80%, Fe: 15%, Mo: 5% plus trace amounts of S, C, Mn, Si, & P
Attenuation is the ratio of the magnetic field strength on one side of the foil
compared to the field strength on the other side.
You can estimate the amount of magnetic field reduction (Attenuation)
produced by a cylinder of .004" Magnetic Shielding Foil of a given Diameter (D, in inches)
if you know the Permeability (P), with this formula:
Attenuation = 0.004 x P/D
For example: You would expect a 8:1 reduction (88%)
from a 10" cylinder in a 1 kHz field where permeability is about 20000
Attenuation = .004 x 20000/10 = 8
Shielding Foil Installation Notes:
1) Cylindrical shapes generally provide more shielding than flat layouts.
2) Allow at least 1" overlap & achieve good foil-to-foil contact at all seams.
3) Do not solder or weld. Heating permanently reduces shielding effectiveness.
4) Spacer shims of 1/16" to 1/8" between layers improves shielding effectiveness.
5) Avoid sharp angle bends in the alloy.
6) Foil can be glued, screwed, nailed, taped, riveted or stapled to a supporting surface.
7) Use metal primer first if you are going to paint the foil.
8) Apply protective covering to all exposed edges. They are SHARP!
Price is per linear foot. Please enter the the desired length (per linear ft) in the quantity box |
21.95 |
View |
|
Mumetal Wire
Do you have an application requiring Mumetal? in un-insulated wire format? We have it in two different diameters!
Stress annealed Mumetal?
alloy. Wind it, weave it, braid it. Create toroids, coils, chains or
simply experiment with its unique properties! Be the first to create a
truly magnetic shielded garment!
Cost of product is per pound. For more pounds of wire please order more than one spool.
Note:
.005" wire yields approximately 13400 ft per pound
.025" wire yields approximately 530 ft per pound
Chemical Analysis (%):
S:
C:
Mn:
Si:
Ni:
Mo:
P:
Fe:
.0006
.0044
.502
less than .010
80.00
5.0
.0035
balance
Mechanical Specifications
Specific Gravity:8.74
Coefficient of Expansion:12.6 x 10-6 per ?C
Tensile Strength:85 x 10? PSI
Melting Point:1454?C
Thermal Conductivity:0.138 cal/sec/cm?/cm/?C at 20?C
Minimum Operating Temp:4?K
Grain Size:10
Hardness:HV 0.3 = 188
Anneal:Stress
Specification:MIL N 14411c
Electromagnetic Specifications
Electrical Resistivity:
Saturation Induction (10 OE):
Maximum Permeability:
Induction at m max.:
Coercive Force:
Curie Temp:
330 ohms/cir mil-foot
7500 Gauss
325,000
3000
.007 Hc, Oersteds
850?F or 454?C
|
75.00 |
View |
|
Joint Shield
When you need more than one Mag-Stop Plate to
cover an area, how do you handle the joints? Joint-Shield is the
perfect solution! This is a generous .010" thick, fully hydrogen
annealed magnetic shielding alloy with adhesive backing (rated 0 -
200?F) on one side. Simply butt the Mag-Stop plates tightly together,
and "tape" over the seam with Joint-Shield high permeabilty alloy. This
method offers much less bulk and better appearance than the old overlap
technique and provides excellent shielding integrity. Simple to use:
just cut to desired length with a heavy scissors, peel the protective
backing and press into place!
Joint-Shield can also be used by itself as an excellent magnetic
shielding material when a 4" width and adhesive backing is desirable
(wrap it around wiring and conduit, speaker magnets, even small
appliances like shavers and hair dryers!). Joint-Shield can be shaped
by hand, without the need for special tools, but watch the sharp
edges.
Mechanical Specifications
Specific Gravity:
Coefficient of Expansion:
Tensile Strength:
Yield Strength:
Mod. of Elasticity:
Hardness (Rockwell B):
Melting Point:
Thermal Conductivity:
Minimum Operating Temp:
Curie Temp:
8.74
12.6 x 10-6 per ?C
64 x 10? PSI
18.5 x 10? PSI
25 x 106
50 Ref
1454?C
0.138 cal/sec/cm?/cm/?C at 20?C
4?K
400?C
Electromagnetic Specifications
Anneal:
Electrical Resistivity:
Saturation Induction:
Initial Permeabilty:
Permeability at 40 B:
Permeability at 200 B:
Maximum Permeability:
Induction at m max.:
Coercive Force:
hydrogen
330 ohms/cir mil-foot
8000 Gauss
30,000
75,000
135,000
450,000
3000
.015 Hc, Oersteds
General Information:
Pressure sensitive adhesive (peel and stick) on one side of the
material permits quick and easy prototype and shield fabrication by
hand. The material exhibits an aesthetically clean and bright metallic
surface. The annealing process leaves the alloy "dead soft" so it
should be protected from denting and scratches. Bending is possible,
but gently rounded bends are favorable to sharp creases and acute
angles. Great care should be taken to avoid heating
this material above 400?C since heating will affect the grain size and
deteriorate shielding properties. Unfinished edges may be sharp so care
should be taken during handling, and proper finishing of edges is
required to protect end user.
Maintenance:Because of its high nickel content, this alloy
is highly corrosion resistant. Cleaning is simple with a soft cloth, or
you can use mild soapy water (be sure to rinse well and dry). If
required for cosmetic purposes, this material can be spray painted or
adhesive veneers may be applied.
|
19.95 |
View |
|
Conductive Marker
Need a conductive liquid but don't need a whole quart? Use this unique
marker to draw real silver conductive lines with precision and control
to repair circuits, jump across connections, apply shielding to a small
area, or even repair your auto windshield defroster! Valved marker tip
for easy application. Can be soldered at low temperatures. Dries
quickly with no special equipment. 8.5 grams goes a long way. Perfect
for designing prototype circuits too! Air dry in 45 minutes, or heat
dry for 5 minutes at 250-300? F. Caution: uses volatile solvents.
Safety Data |
19.95 |
View |
|
Conductive Epoxy
Excellent electrical conductivity and high strength conductive bonding
combined with convenience. Repairs defective traces and creates jumpers
to board. Allows you to make quick solderless electronic connections.
Connect ground cord to conductive fabrics and garments. Two Part
Epoxy?easy 1:1 mixing ratio. Bonds heat sensitive components without
soldering. Makes surface mount connections, no drilling required! 14
gr. total. |
25.95 |
View |
|
Conductive Grease
Conductive lubricant containing pure silver provides superior
electrical and thermal conductivity, lubrication and protection. Handy
syringe dispenser permits precise control and no mess. Effectively
lubricates metal, rubber and plastic. Protects against moisture and
corrosion. Thermally stable over a wide temperature range. Reduces wear
too. 0.23 oz.
|
19.95 |
View |
|
Silver Print Conductive Ink
This conductive coating consists of finely
divided silver powder in a methyl methacrylate binder. It can be
applied by brush, screen, dip or spray. Suitable for application to
most materials: paper, films, plastic, rubber, wood, metal or ceramic
and it air dries at room temperature in 16-20 hours or it can be forced
dried at 140?F for 1 hour. The coating must be fully dried to achieve
maximum conductivity.
Uses include PC repair, add-on circuit traces,
electrical contacts where solder is not practical, shielding seams and
small gaps. Electrical resistance of a 1 mil dry coating will be
approximately 0.2 Ohm/sq. or less.
It is extremely important to keep the material
thoroughly mixed during application as the silver particles do settle
out of suspension rather quickly. Butyl acetate can be used as a
thinner. Coverage at 2.0 mil is approximately 18 in?/gram. Supplied in
0.75 oz bottle.
Click here to view safety info
|
29.95 |
View |
|
Super Shield
A general purpose EMI/RFI shielding in a handy aerosol spray for use on
most substrates. Especially good for RF shielding plastic electronics
enclosures. Consists of a tough, durable acrylic base pigmented with a
high purity nickel flake. One to two mil coating provides 40dB - 50dB
shielding across a frequency range of 5 to 1800MHz. About 1600 in?/can
coverage at 1.5 mil. Contains no CFC 'S, NO HCFC'S, ozone friendly.
340g (12 oz) aerosol can. Dries to a dull gray color.
Volume Resistivity: 1 Ohm - mil
Dry time: 10 minutes at room temperature
Recoat time: 5 minutes
Excellent adhesion to most plastics
Tested as per IEEE Std. 299-1997
Underwriters Laboratories Recognized File No.: E202609
Click to see safety info
|
31.95 |
View |
|
Mag-Stop Plate - Stress Annealed
Now achieve excellent and affordable magnetic shielding in difficult situations! Mag-
Stop Plates are extra thick high-efficiency magnetic alloy (Mumetal?) plates, specially designed to
provide superior shielding for electric circuit boxes, side by side computer users, and any
situation where you need a flat shielding material on a wall, floor, or ceiling. Can be
mounted with ordinary nails or screws, or sandwiched between the studs and dry-wall.
Use zinc chromate primer before painting. In one application, we were able to achieve almost 95% attenuation of a
200 mG field!
The 24" wide "stress annealed" plates offer good magnetic shielding and
are also well-suited
for forming into complicated shapes.
Application Note for Joining Plates:
There are two effective ways to achieve shielding continuity between multiple plates:
1) overlap 2" at the joints, ensuring good metal-to-metal contact
2) butt joints tightly and cover over the joints with
Joint Shield
General Information:
The material exhibits an aesthetically clean and bright metallic
surface. The annealing process leaves the alloy "dead soft" so it
should be protected from denting and scratches. Bending is possible,
but gently rounded bends are favorable to sharp creases and acute
angles. Great care should be taken to avoid heating
this material above 400? C since heating will affect the grain size and
deteriorate shielding properties. Unfinished edges may be sharp so care
should be taken during handling, and proper finishing of edges is
required to protect end user.
Maintenance:Because of its high nickel content, this alloy
is highly corrosion resistant. Cleaning is simple with a soft cloth, or
you can use mild soapy water (be sure to rinse well and dry). If
required for cosmetic purposes, this material can be spray painted or
adhesive veneers may be applied.
SPECIFICATIONS:
Thickness: 0.004"
Temper: Stress Annealed
Specification: MIL N 14411c
Grain Size: 10
Hardness: HV 0.3 = 188
Coercive Force: HC = 0.007 Oersteds
Max. Permeability: MUMAX = 325000
Saturation Induction: B (10 OE) = 7500 G
Chemical Analysis:
Ni: 80%, Fe: 15%, Mo: 5% plus trace amounts of S, C, Mn, Si, & P
Details
Size (W x L x T inches)
Approx. Weight
24 x 120 x .020"
19 lbs.
24 x 120 x .040"
38 lbs.
24 x 120 x .062"
57 lbs.
|
1194.00 |
View |
|
|
Mag-Stop Plate - Hydrogen Annealed
Now achieve excellent and affordable magnetic shielding in difficult situations! Mag-
Stop Plates are extra thick high-efficiency magnetic alloy (Mumetal?) plates, specially designed to
provide superior shielding for electric circuit boxes, side by side computer users, and any
situation where you need a flat shielding material on a wall, floor, or ceiling. Can be
mounted with ordinary nails or screws, or sandwiched between the studs and dry-wall.
Use zinc chromate primer before painting. In one application, we were able to achieve almost 95% attenuation of a
200 mG field!
The 30" wide "fully hydrogen
annealed" plates offer the best shielding available (up to 10 times the
shielding effectiveness of stress-annealed alloy) and should not be
soldered, welded, or heated in any way. Hydrogen annealed plates have 2
small holes pre-drilled near one end which may be used for mounting.
Application Note for Joining Plates:
There are two effective ways to achieve shielding continuity between multiple plates:
1) overlap 2" at the joints, ensuring good metal-to-metal contact
2) butt joints tightly and cover over the joints with Joint Shield
General Information:
The material exhibits an aesthetically clean and bright metallic
surface. The annealing process leaves the alloy "dead soft" so it
should be protected from denting and scratches. Bending is possible,
but gently rounded bends are favorable to sharp creases and acute
angles. Great care should be taken to avoid heating this material above 400? C since heating will affect the grain size and
deteriorate shielding properties. Unfinished edges may be sharp so care
should be taken during handling, and proper finishing of edges is
required to protect end user.
Maintenance:
Because of its high nickel content, this alloy
is highly corrosion resistant. Cleaning is simple with a soft cloth, or
you can use mild soapy water (be sure to rinse well and dry). If
required for cosmetic purposes, this material can be spray painted or
adhesive veneers may be applied.
Mechanical Specifications
Specific Gravity:
8.74
Coefficient of Expansion:
12.6 x 10-6 per ?C
Tensile Strength:
64 x 10? PSI
Yield Strength:
>18.5 x 10? PSI
Mod. of Elasticity:
25 x 10? PSI
Hardness (Rockwell B):
50 Ref.
Melting Point:
1454?C
Thermal Conductivity:
0.138 cal/sec/cm?/cm/?C at 20?C
Minimum Operating Temp:
4?K
Curie Temp:
400?C
Electromagnetic Specifications
Electrical Resistivity:
330 ohms/cir mil-foot
Saturation Induction:
8000 Gauss
Initial Permeabilty:
30,000
Permeability at 40 B:
75,000
Permeability at 200 B:
135,000
Maximum Permeability:
450,000
Induction at m max.:
3000
Coercive Force:
.015 Hc, Oersteds
Details
Size (W x L x T inches)
Approx. Weight
30 x 29 x .020"
6 lbs.
30 x 59 x .020"
12 lbs.
30 x 29 x .040"
11 lbs.
30 x 59 x .040"
23 lbs.
30 x 29 x .062"
17 lbs.
30 x 59 x .062"
35 lbs.
|
498.00 |
View |
|
Silver Lining paint - Quart
Need high grade RF shielding in a water base? Silver Lining is
non-toxic because it is a one component acrylic latex coating using
silver particles for conductivity. Cleans up with water like ordinary
house paint. Can be rolled or brushed. Compatible with almost all
plastics. A quart covers about 120 ft? per 2 mil application.
Resistivity is <0.4 ohm/sq. at 2 mils, attenuation is 80 dB over 1
MHz ? 10 GHz. For interior or exterior application, but a protective
topcoat is recommended when used outdoors. Flat gray finish.
|
159.95 |
View |
|
|
Silver Lining Paint - Gallon
Need high grade RF shielding in a water base? Silver Lining is
non-toxic because it is a one component acrylic latex coating using
silver particles for conductivity. Cleans up with water like ordinary
house paint. Can be rolled or brushed. Compatible with almost all
plastics. Resistivity is |
459.95 |
View |
|
Magic Wall Paint 1 quart
A very unique item! Non-toxic, non-flammable, and non-hazardous, you
can paint this magnetic paint onto practically any surface that will
take a latex paint and then magnets will stick to it. Is your
refrigerator door running out of space for notes and pictures? Kids
want to hang things on the wall but you don't want the tape/tack marks?
Workshop needs more organizing space? Simply paint the wall, ceiling,
blackboard, bulletin board, kitchen cabinets (you can topcoat with your
favorite latex color) with magnetic paint, then post whatever you like
with magnets.
Owes its unique properties to the inclusion of
low corrosion iron filings in a water based latex. Brush or roll on.
Cleans up easily with water. Bonus: this paint actually provides a
slight amount of ELF magnetic shielding! Color is gray.
One quart of paint. Larger volumes are avaiable in the below options menu. |
29.95 |
View |
|
Metglas
Space-age technology has produced this unique ultra-high permeability
(1,000,000+) magnetic shielding alloy. Unlike conventional Mumetal?
shielding alloys which are nickel/iron based and depend on bulk for
effectiveness, MetGlas is a cobalt based alloy which is only 0.00065"
thick (that's 16 microns, a red blood cell is 8 microns across)!
Thinner means less material is needed. Less material means less weight
and lower cost. Easy to handle, too. Cut it with a scissors,
shape it with your fingers, tape it in place. Flexible and tough, with
moderate corrosion resistance, it can be used indoors or out. Near-zero
magnetostriction means it can be flexed over and over without losing
its shielding properties.
Wrap wiring, pipes, switches, or
electro-magnets. We were able to achieve over 95% reduction of fields
from a lamp cord by wrapping it in a single layer of this material!
Make shields for your shavers, electric toothbrushes, hair dryers,
alarm clocks or lighting ballasts. Even lay it flat (in our
experiments, we saw nearly 90% field reduction when a 4" x 4" MetGlas
shield was placed flat against an energized lamp cord). Note:
This material tends to saturate easily and is not recommended for
shielding strong magnetic fields. This is the material often used in
Electronic Article Surveillance systems. Formula 2714AZ, supplied
annealed.
Electromagnetic Properties
Saturation Induction (Tesla)
0.57
Maximum DC Permeability (?):
1,000,000
Saturation Magnetostriction (ppm)
|
2.50 |
View |
|
|
Metglas - 1 pound spool
Space-age technology has produced this unique ultra-high permeability
(1,000,000+) magnetic shielding alloy. Unlike conventional Mumetal?
shielding alloys which are nickel/iron based and depend on bulk for
effectiveness, MetGlas is a cobalt based alloy which is only 0.00065"
thick (that's 16 microns, a red blood cell is 8 microns across)!
Thinner means less material is needed. Less material means less weight
and lower cost. Easy to handle, too. Cut it with a scissors,
shape it with your fingers, tape it in place. Flexible and tough, with
moderate corrosion resistance, it can be used indoors or out. Near-zero
magnetostriction means it can be flexed over and over without losing
its shielding properties.
Wrap wiring, pipes, switches, or
electro-magnets. We were able to achieve over 95% reduction of fields
from a lamp cord by wrapping it in a single layer of this material!
Make shields for your shavers, electric toothbrushes, hair dryers,
alarm clocks or lighting ballasts. Even lay it flat (in our
experiments, we saw nearly 90% field reduction when a 4" x 4" MetGlas
shield was placed flat against an energized lamp cord). Note:
This material tends to saturate easily and is not recommended for
shielding strong magnetic fields. This is the material often used in
Electronic Article Surveillance systems. Formula 2714AZ, supplied
annealed.
Electromagnetic Properties
Saturation Induction (Tesla)
0.57
Maximum DC Permeability (?):
1,000,000
Saturation Magnetostriction (ppm)
<<1
Electrical Resistivity (? Ohm-cm)
142
Curie Temperature (?C)
225
Physical Properties
Density (g/cc)
7.59
Vicker's Hardness (50g load)
960
Tensile Strength (MN/m?)
1,000-1,700
Elastic Modulus (GN/m?)
100-110
Thermal Expansion (ppm/?C)
12.7
Continuous Service Temp. (?C)
90
Composition
Ni: 1.63%
Fe: 4.45%
Si: 8.60%
B: 3.15%
Co: 82.17%
Installation Instructions
Place Metglas as close as possible to the source of the field for best results.
Use an insulator to avoid direct contact between Metglas and covered metal conduits or wires.
Enclose the source (cylinder shapes) whenever possible.
Overlap and tape all seams for good metal-to-metal contact.
Avoid sharp bends and don't use helix (spiral) shapes.
Do NOT allow Metglas to contact live bare wires to avoid electrical shock!
And of course, be careful of the edges, as they may be sharp.
|
599.00 |
View |
|
Cupro-Cote Paint - Gallon
This is a sprayable, brushable, or rollable conductive metallic coating using a specially formulated copper
as the conductive agent for superior performance in electric field and
RF shielding. Developed initially as an RFI/EMI shield for plastic
electronic equipment housings, it can be applied directly onto acrylic,
ABS and structural foams, as well as solvent sensitive materials such
as polycarbonate and polystyrene. Can also be applied to other
non-porous surfaces including primed wallboard, wood and clean metals.
Can be applied by sprayer, brush or roller just like ordinary latex
paint! Just as safe to handle, too. Thin with water. Amazing surface
resistivity of |
459.95 |
View |
|
|
Cupro-Cote Paint - Quart
This is a sprayable, brushable, or rollable conductive metallic coating using a specially formulated copper
as the conductive agent for superior performance in electric field and
RF shielding. Developed initially as an RFI/EMI shield for plastic
electronic equipment housings, it can be applied directly onto acrylic,
ABS and structural foams, as well as solvent sensitive materials such
as polycarbonate and polystyrene. Can also be applied to other
non-porous surfaces including primed wallboard, wood and clean metals.
Can be applied by sprayer, brush or roller just like ordinary latex
paint! Just as safe to handle, too. Thin with water. Amazing surface
resistivity of |
159.95 |
View |
|
|
Cupro-Cote Paint - 4 Oz
This is a sprayable, brushable, or rollable conductive metallic coating using a specially formulated copper
as the conductive agent for superior performance in electric field and
RF shielding. Developed initially as an RFI/EMI shield for plastic
electronic equipment housings, it can be applied directly onto acrylic,
ABS and structural foams, as well as solvent sensitive materials such
as polycarbonate and polystyrene. Can also be applied to other
non-porous surfaces including primed wallboard, wood and clean metals.
Can be applied by sprayer, brush or roller just like ordinary latex
paint! Just as safe to handle, too. Thin with water. Amazing surface
resistivity of |
29.95 |
View |
|
Snap/Ring Terminal Combo
Want a tidy and good looking way to attach a ground cord to a
conductive fabric or plastic shield? This simple hardware combination
does the trick in style. First, crimp the provided ring terminal to
your ground wire. Next, punch a small hole in your conductive sheet.
Pass the stud of the snap through this hole and through the ring
terminal. Finally, apply the other half of the snap. Makes good contact
and you can move it or remove it as needed. Snap is nickel plated for
excellent corrosion resistance and is washable.
Ground wire not
included.
|
2.00 |
View |
|
Grounding Clamp
Copper plated clamp with good jaw tension capable of grabbing ?" to 1"
diameter pipe, screw or bar. Use these to attach ground cord to your
plumbing, or to metal stakes in the ground. Crimps easily to cord. 3"
length overall.
Ground cord not
included.
|
4.95 |
View |
|
Shielded Plug Cord
Typical lamp cords, appliance cords, even the cord to your alarm clock
emit strong electric fields even if the appliance is turned off.
Replacing the cord with a shielded cord eliminates this source of
electric field. Replacement is simple, but does require basic knowledge
of wiring.
Our recycled shielded cords are rated for 10 amps, 6 ft long. 3-prong
plug on one end, other end cut. Internal metallic shielding. Black
vinyl.
|
4.95 |
View |
|
Alligator Clips - Pair
High quality alligator clips for grounding and conductivity uses. Will grab foils, fabrics,
chassis, grounding wires, screws, and small posts.
Attach to just about any copper wire with solder or crimp. Each pack contains a pair of alligator clips.
|
2.00 |
View |
|
|
Ring Terminal - Pair
Each pack contains a pair of ring terminals |
2.95 |
View |
|
Ex-static Fabric
A light weight, durable conductive fabric. 87% polyester, 13% gray BASF
Resistat (carbon) fibers woven right into the fabric in an attractive
diamond pattern providing surface resistivity of 105
ohms per square. Very comfortable, only 3 oz per square yard, it cuts,
sews, and washes like any polyester fabric! Conductivity will hold up
to 50 or more low heat washings. Can be used to make E-field shielding
bedding, appliance covers, clothing, drapes, room dividers, and
anything else you can sew. Some people claim they can sleep noticeably
better when they sandwich conductive fabric into their bedsheets. One
woman we know wears it on her head as a scarf and swears it reduces EMF
noise for her! Available in 60" width. Color is White with Gray diamond
pattern.
|
4.95 |
View |
|
|
Ex-static Fabric - 100' roll
A light weight, durable conductive fabric in a 100' roll. 87% polyester, 13% gray BASF
Resistat (carbon) fibers woven right into the fabric in an attractive
diamond pattern providing surface resistivity of 105
ohms per square. Very comfortable, only 3 oz per square yard, it cuts,
sews, and washes like any polyester fabric! Conductivity will hold up
to 50 or more low heat washings. Can be used to make E-field shielding
bedding, appliance covers, clothing, drapes, room dividers, and
anything else you can sew. Some people claim they can sleep noticeably
better when they sandwich conductive fabric into their bedsheets. One
woman we know wears it on her head as a scarf and swears it reduces EMF
noise for her! Available in 60" width. Color is White with Gray diamond
pattern.
|
371.25 |
View |
|
Conductive Tubing
Composed of electrically conductive black polyethylene and great for
shielding electrical cords. It's easy to slide any electrical cord
(even fits those giant dryer plugs!) through this 4" wide (when flat)
sleeve without having to remove the plug from the end of the cord.
Surface resistivity <1000 ohms/square. Only 4 mil thick, it won't
hold up to tearing, heat or abuse, but it's tough enough to do a great
job on the lamp cord by your bed, the air conditioner cord, or even
cables in your car. Use a grounding cable, and please be careful when
handling electrical cords.
|
1.15 |
View |
|
The Earthcalm Scalar Unit for EMF sensitive people
A note from the inventor of EarthCalm Products | EarthCalm Testimonials | EarthCalm FAQ's | EarthCalm Brochure | What is the Schumann Resonance? | What is the difference between an EarthCalm Resonator and the Q-Link pendant? | Cell Phone and Cordless Phone protection | Headaches & Migraines | Fibromyalgia & Electrical Sensitivity | Children, ADHD & Asthma | Protect yourself
Free Shipping on this Item!
Get 10% off when you buy TWO or more EarthCalm productsWe give you this 10% off package using the EarthCalm Home or Office Unit and the EarthCalm Resonator as the combination of these items produces better results
"EarthCalm products never need "recharging" and are offered with a 90 day money back guarantee to encourage you to experiment with this product yourself. This item can be returned in 90 days for a credit minus a $7.99 shipping fee for the 48 States."
The Scalar Home Protection System includes a three-step system to moderate the adjustment period, which is important to everybody but essential for people who are electrically sensitive or who have immune deficiency problems. Because it provides full 14 circuit protection the System is also ideal for families with young children. Children are more vulnerable to EMFs than adults due to their developing nervous systems. Given the current high exposure levels in schools and in the home, it is important to provide them with maximum protection.
The Scalar Home Protection System is ideal in the sense that you simply install the System and forget about it. No need to worry about children or young adults losing Resonators, etc. Parents sometimes ask if their children need Resonators at school. Because healing occurs for the most part during sleep, it is not necessary for children or teenagers to have personal protection while at school. When they get older and work in front of a computer, then a personal Resonator should be considered.
During a period of adaptation, minor healing symptoms may or may not occur as the stress level in the home is gradually lowered. Some people will have minor symptoms such as dizziness or fatigue. The System includes three levels of EMF protection to build up to the maximum of a scalar ground slowly so as to avoid or minimize possible uncomfortable detoxification symptoms.
The Scalar Home Protection System utilizes the principles of cyclotronic resonance and Scalar Resonance Technology. EarthCalm products never need recharging and are offered with a 90 day money back guarantee to afford you the time to monitor the effectiveness yourself. Note and jot down your specific symptoms now as well as those of your family, and then compare them after using our Scalar Home Protection System for several weeks to determine their effectiveness for yourself.
Contains 14 circuits.
Specifications: Measures: 4” x 2” x 2”. May be plugged into any 3 hole (or two hole with plug adapter) outlet anywhere in the home to protect an entire house. For 220 voltage order the worldwide version which is slightly smaller in size.
"Returns: When returning this product it must be accompanied with all its packaging and related paperwork to receive a refund"
Remember to select the Shipping option 'Free Shipping' in the checkout area or you will not receive Free Shipping for this product. |
298.00 |
View |
|
Ground Stake Kit 25ft
If you don?t like the idea of grounding your shielding paint, fabric or plastic through your building?s electrical system, you can use this simple and durable grounding stake to connect directly to the Earth. Sturdy, rust resistant, 36 inch long aluminum stake is ready to drive into the soil. Complete with exterior grade heavy gauge ground cord (with no terminal) and stake-to-cord connector.
Note: if soil is rocky, you may need to dig a hole first with appropriate tools. Be careful when selecting location? do not place near buried wires or pipes. |
19.95 |
View |
|
|
Ground Stake Kit 50ft
If you don?t like the idea of grounding your shielding paint, fabric or plastic through your building?s electrical system, you can use this simple and durable grounding stake to connect directly to the Earth. Sturdy, rust resistant, 36 inch long aluminum stake is ready to drive into the soil. Complete with exterior grade heavy gauge ground cord (with no terminal) and stake-to-cord connector.
Note: if soil is rocky, you may need to dig a hole first with appropriate tools. Be careful when selecting location? do not place near buried wires or pipes. |
29.95 |
View |
|
|
Ground Stake Kit 100ft
If you don?t like the idea of grounding your shielding paint, fabric or plastic through your building?s electrical system, you can use this simple and durable grounding stake to connect directly to the Earth. Sturdy, rust resistant, 36 inch long aluminum stake is ready to drive into the soil. Complete with exterior grade heavy gauge ground cord (with no terminal) and stake-to-cord connector.
Note: if soil is rocky, you may need to dig a hole first with appropriate tools. Be careful when selecting location? do not place near buried wires or pipes. |
39.95 |
View |
|
Velostat Film
It's plain black, shiny and big! Velostat is a very low cost, extra-wide conductive sheet for electric field shielding. Carbon impregnated black polyethylene film. Normal 4 mil or heavy duty 8 mil thick so it's really tough and 36" wide to cover large projects. Volume resistivity is |
1.95 |
View |
|
|
Magnetic Shielding Foil 15inch wide, 0.010inch thick
Price is per linear foot. Please enter the the desired length (per linear ft) in the quantity box
Used for years in industry to shield delicate electronic components
from EMFs, magnetic shielding alloy is now available at affordable
prices for home and office use. This 80% nickel alloy is easy to trim
with scissors and shape by hand. Can be formed into magnetic barriers
on cellular phones, microwave ovens, doorbell transformers, VDTs,
buried wiring, and more. With snug fitting shapes, get as much as 75%
attenuation of the magnetic field with one thickness. Use multiple
layers for even greater reduction. Foil is available in two sizes and
can be ordered in any length. (We recommend the use of a
gaussmeter
to determine the proper shape and positioning of the magnetic shield,
and to confirm that the fields have been adequately reduced.)
CAUTION: Foil has sharp edges!
SPECIFICATIONS:
Thickness: 0.004"
Temper: Stress Annealed
Specification: MIL N 14411c
Grain Size: 10
Hardness: HV 0.3 = 188
Coercive Force: HC = 0.007 Oersteds
Max. Permeability: MUMAX = 325000
Saturation Induction: B (10 OE) = 7500 G
Chemical Analysis:
Ni: 80%, Fe: 15%, Mo: 5% plus trace amounts of S, C, Mn, Si, & P
Attenuation is the ratio of the magnetic field strength on one side of the foil
compared to the field strength on the other side.
You can estimate the amount of magnetic field reduction (Attenuation)
produced by a cylinder of .004" Magnetic Shielding Foil of a given Diameter (D, in inches)
if you know the Permeability (P), with this formula:
Attenuation = 0.004 x P/D
For example: You would expect a 8:1 reduction (88%)
from a 10" cylinder in a 1 kHz field where permeability is about 20000
Attenuation = .004 x 20000/10 = 8
Shielding Foil Installation Notes:
1) Cylindrical shapes generally provide more shielding than flat layouts.
2) Allow at least 1" overlap & achieve good foil-to-foil contact at all seams.
3) Do not solder or weld. Heating permanently reduces shielding effectiveness.
4) Spacer shims of 1/16" to 1/8" between layers improves shielding effectiveness.
5) Avoid sharp angle bends in the alloy.
6) Foil can be glued, screwed, nailed, taped, riveted or stapled to a supporting surface.
7) Use metal primer first if you are going to paint the foil.
8) Apply protective covering to all exposed edges. They are SHARP!
Price is per linear foot. Please enter the the desired length (per linear ft) in the quantity box |
31.95 |
View |
|
ESD Static Fabric
This is an interesting mesh material. Very fine (0.08 mm) 316L Stainless steel wire is knitted with 40% polyester yarn to create a stretchy fabric that is easy to touch and wash, but wears tough. Highly conductive in transverse direction (2.2 Ohm per sq) and ample 1000 Ohm per sq conductivity longitudinally. Great for static control. Make seat or bed covers, computer covers, overgarments etc. 152 gr/m˛. One meter wide. Gray. |
11.95 |
View |
|
LIFE Energy Keychain Shields™
Tone down heavy automotive energy when placed inside a vehicle. The amount of the EMFs (Electro Magnetic Frequencies) from your car's electrical fields is very high. These negative frequencies are emitted by all cars and are especially high in hybrid and electrical cars. This can be measured by using an
EMF
meter and these negative energies can run right under the car seats and effect children to adults. The LIFE Energy Shield™, at the same time that they are protecting you from these negative frequencies, protects the body from the harmful effects of EMFs (Electro Magnetic Frequencies) from electrical fields, microwaves, radio waves, and other weakening fields by emitting healing frequencies that have a positive, balancing effect on the glands, organs, and meridians of the body.
5 Reasons Why You Need Protection from your Laptopor your Car, Cell Phone, Television, Hair Dryer, Microwave, Refrigerator, Electric Blanket, Iron, Electric Stove, Microwave, Toaster, Computer, Blender, Stereo Receiver, not to mention Power Lines...
Your body is a series of electrical impulses and currentsEMFs disrupt some of these functionsYou are bombarded by EMFs on a daily basisEffects of long-term exposure include chronic fatigue, nausea,cataracts, heart problems, brain tumors, miscarriages, and cancer.Short of living in a cave, it is hard to avoid EMFs
What Can You Do About It?Order your LIFE Energy Shield™ Today!Call (888) 688-8889
Electronic devices that emit EMF are everywhere. Life wouldn't be the same without these modern marvels. But are these devices harming you? What are EMF Emissions and Are They Dangerous?
Electromagnetic fields are formed wherever electricity flows. The greater the current or voltage, the stronger the field. Household electronic devices such as cordless phones and microwaves all emit low doses of EMF. Now consider how many of these devices you have around you at all times -- computers, cell phones, even your car -- you are constantly bombarded by EMFs.
Right, but are they dangerous?Small electrical currents exist in the human body as part of the natural chemical reactions that take place, such as brain activity, digestion, and your pumping heart.
"Low-frequency magnetic fields induce circulating currents within the human body. The strength of these currents depends on the intensity of the outside magnetic field. If sufficiently large, these currents could cause stimulation of nerves and muscles or affect other biological processes." -- World Health Organization
Although your daily exposure to EMF isn't like sitting inside a microwave oven, the long-term effects of such exposure can have damaging effects at a cellular level. Dr. David Carpenter, MD and Director of the Institute for Health & the Environment at the University at Albany, believes it is likely that up to 30% of all childhood cancers come from exposure to EMFs. Numerous worldwide studies link EMFs to serious health problems such as leukemia, miscarriages, chronic fatigue, forgetfulness and nausea. Even the EPA once recommended in March 1990 that EMFs be classified as a Class B carcinogen alongside formaldehyde, DDT and PCBs. (Subsequent protests from utility, military and computer lobbyists resulted in EMFs remaining unclassified.)
How Can I Protect Myself from EMFs?LIFE Energy Shields™ have been designed using techniques derived from quantum physics. The most effective frequencies have been encoded and imprinted in the silicone structure of the LIFE Energy Shields™ using advanced biofeedback and electro-dermal screening equipment. A combination of proprietary frequencies have been sealed permanently into these shields, which ave been tested to strengthen all bio-functions through their resonance.
How Are LIFE Energy Shields™ Different from Other Products?Unlike other shields that only address EMF and microwave frequencies, LIFE Energy Shields™ balance the body against these frequencies and also balance all energy meridians of the body for optimum health.
These shields bring greater balance to the whole body. Users have reported more vibrant energy, reduced fatigue, better sleep, and optimized performance. LIFE Energy Shields™ are imprinted with frequencies that help you resist stress and stay focused, and are produced by health care practitioners with over 30 years of experience in the natural healthcare field. |
29.97 |
View |
|
LIFE Energy Laptop/Microwave/Television Shields™
Tone down the heavy energy produced by microwaves, televisions and computers by attaching to appliances and electronics.
5 Reasons Why You Need Protection from your Laptopor your Car, Cell Phone, Television, Hair Dryer, Microwave, Refrigerator, Electric Blanket, Iron, Electric Stove, Microwave, Toaster, Computer, Blender, Stereo Receiver, not to mention Power Lines...
Your body is a series of electrical impulses and currentsEMFs disrupt some of these functionsYou are bombarded by EMFs on a daily basisEffects of long-term exposure include chronic fatigue, nausea,cataracts, heart problems, brain tumors, miscarriages, and cancer.Short of living in a cave, it is hard to avoid EMFs
What Can You Do About It?Order your LIFE Energy Shield™ Today!Call (888) 688-8889
Electronic devices that emit EMF are everywhere. Life wouldn't be the same without these modern marvels. But are these devices harming you? What are EMF Emissions and Are They Dangerous?
Electromagnetic fields are formed wherever electricity flows. The greater the current or voltage, the stronger the field. Household electronic devices such as cordless phones and microwaves all emit low doses of EMF. Now consider how many of these devices you have around you at all times -- computers, cell phones, even your car -- you are constantly bombarded by EMFs.
Right, but are they dangerous?Small electrical currents exist in the human body as part of the natural chemical reactions that take place, such as brain activity, digestion, and your pumping heart.
"Low-frequency magnetic fields induce circulating currents within the human body. The strength of these currents depends on the intensity of the outside magnetic field. If sufficiently large, these currents could cause stimulation of nerves and muscles or affect other biological processes." -- World Health Organization
Although your daily exposure to EMF isn't like sitting inside a microwave oven, the long-term effects of such exposure can have damaging effects at a cellular level. Dr. David Carpenter, MD and Director of the Institute for Health & the Environment at the University at Albany, believes it is likely that up to 30% of all childhood cancers come from exposure to EMFs. Numerous worldwide studies link EMFs to serious health problems such as leukemia, miscarriages, chronic fatigue, forgetfulness and nausea. Even the EPA once recommended in March 1990 that EMFs be classified as a Class B carcinogen alongside formaldehyde, DDT and PCBs. (Subsequent protests from utility, military and computer lobbyists resulted in EMFs remaining unclassified.)
How Can I Protect Myself from EMFs?LIFE Energy Shields™ have been designed using techniques derived from quantum physics. The most effective frequencies have been encoded and imprinted in the silicone structure of the LIFE Energy Shields™ using advanced biofeedback and electro-dermal screening equipment. A combination of proprietary frequencies have been sealed permanently into these shields, which ave been tested to strengthen all bio-functions through their resonance.
How Are LIFE Energy Shields™ Different from Other Products?Unlike other shields that only address EMF and microwave frequencies, LIFE Energy Shields™ balance the body against these frequencies and also balance all energy meridians of the body for optimum health.
These shields bring greater balance to the whole body. Users have reported more vibrant energy, reduced fatigue, better sleep, and optimized performance. LIFE Energy Shields™ are imprinted with frequencies that help you resist stress and stay focused, and are produced by health care practitioners with over 30 years of experience in the natural healthcare field. |
49.97 |
View |
|
|
|
|
